Design your own cabinets, for home or business
A free design program in five steps: the cabinets, the hardware, the colours, then your specification and a PDF. Tap the big buttons and watch your drawing grow.
New here? How the design program works
- What to design. Pick home or business and the rooms you need.
- Cabinets. Pick the shape: one wall, an L, a U or a galley, with an island if you like. Each wall has a letter, on a small map and on the buttons above the drawing; tap one to work on that wall. Enter a wall's size if you know it, then add, remove and drag cupboards, appliances, fillers, panels and gaps. Tap any piece in the drawing to change it.
- Hardware. Choose handles and hinges. The moving demo shows how they work.
- Colours and materials. Pick board colours, the benchtop and the kickboard height. You can skip colours and decide later.
- Review and send. See your whole design in 3D, check your choices, download a PDF and send the design to us with your details.
- mm
- Millimetres. 600 mm is 60 cm. Every size in the program is in mm.
- Kickboard
- The strip along the floor under the bottom cupboards.
- Splashback
- The wall between the benchtop and the top cupboards.
- Filler
- A narrow strip, usually 30 to 50 mm, where cupboards meet a wall, so doors and drawers can open past the wall.
- End panel
- A finished panel on the open side of a cupboard run.
- Panel
- A plain board as tall as the cupboards, to fill a wider space, for example from the last cupboard to the wall.
- Gap
- Empty space left on purpose, for example for a bin, a chair or an appliance that stands on its own.
- Bulkhead
- The boxed-in section between the top of the cupboards and the ceiling.
- L-shape, U-shape
- Cupboards along two walls that meet in a corner (L), or three walls (U).
- Galley
- Cupboards along two walls facing each other, with a walkway between.
- Island
- A run of cupboards standing on its own in the room, often with stools on the other side.
- Corner cupboard
- Where two runs meet, a cupboard that reaches into the corner (a "blind corner"). A corner pull-out swings its shelves out to you.
Press 3D above the drawing to see your design in 3D, in your colours. Drag it to turn it round, pinch or use the + and − buttons to zoom, and tap a piece to change it.
Press Picture above the drawing to take a picture of it, from the front, from above or in 3D. Put numbered notes on it or draw on it, download it, and tick it to put it at the end of your PDF.
Your design is kept while this browser tab is open. To keep a copy, download it as a PDF or send it to us.
Is this for a home or a business?
What would you like to design?
It becomes the name of the room in your design. Then you draw it like any other room: cupboards, drawers, shelves and sizes.
Tick at least one room to design.
Kitchen
Set the wall, then add and arrange the cupboards. Tap any piece in the drawing to change it.
Shape
How the cupboards run around the room, seen from above. Pick the picture that looks like yours.
That is fine. A typical wall is drawn for now, and you can enter your size at any time.
Bulkhead
The boxed-in section between the top of the cupboards and the ceiling. Leave it out if your cupboards go to the ceiling or there is open space above them.
Wardrobe doors
Sliding doors run on tracks. Hinged doors swing open. A walk-in robe often has no doors.
Drag any piece in the drawing left or right to move it. Tap a piece to change it.
This piece
Move it, change what it is, or change how wide it is.
Top cupboards
On the wall, above the bench
Bottom cupboards
Under the bench
Tall cupboards
From the floor to the top, like a pantry
Add an appliance or a special cupboard
It goes on the end of the row. Then drag it where you want it. The list shows what usually goes here.
Fillers, panels and gaps
The finishing touches. A filler is a narrow 30 to 50 mm strip where cupboards meet a wall, so doors and drawers can open past it. An end panel finishes the open side of a run. A gap leaves empty space after the piece you picked in the drawing.
Hardware and features
Choose the handles and hinges. The drawing changes as you pick, and the demo shows how they work.
Soft close
Colours and materials
Pick the board colours, then the benchtop and kickboard height. You can skip colours and choose later.
Your pictures
Tap a picture to put notes on it, draw on it or download it. Ticked pictures go at the end of your PDF.
The drawing is a guide only.
Check your design and send it
Your design in 3D
Drag the picture to turn it round and look at it from every side. Your colours, handles and benchtop are shown.
This browser cannot show the 3D view. Your drawings, the PDF and sending your design all still work.
It goes with your pictures, to put notes on and add to your PDF.
